Hawke防爆连接器Hawke Power Ex connector
Hawke防爆连接器Hawke Power Ex connector
上海颐品自动化，：

Hawke防爆连接器Hawke Power Ex connector
Hawke防爆连接器Hawke Power Ex connector
上海颐品自动化，：

Hawke Power Ex connector

Hazardous Area Connector

Tamb: -40°C to +60°C. II2 GD Exdb IIC Extb IIIC Db T85 IP66, 67 & DTS01 deluge protected.

Overview

The Power range of connectors have been designed specifically for the extremely demanding requirements of higher power applications.

Inserts are available with 1 to 4 contacts with a conductor acceptance range of between 50mm² and 630mm² operating up to 780A and 750V as standard. Other voltages available on special request.

Power Connector Dimensions

For connector plugs and connector receptacles, cable glands are required to terminate incoming cables. These can be selected from the cable gland section of our website. These cable glands include but are not restricted to 501/453/Universal and the ICG 653/Universal.

Power Inserts

INSERT SELECTION TABLE
Configuration
Shell Size 32	Shell Size 40	Shell Size 50	Shell Size 63	Shell Size 75
1 x 50mm² + Earth	1 x 185mm² + Earth	3 x 50mm² + Earth	3 x 95mm² + Earth	3 x 185mm² + Earth
1 x 70mm² + Earth	1 x 240mm² + Earth	3 x 70mm² + Earth	3 x 120mm² + Earth	3 x 240mm² + Earth
1 x 95mm² + Earth	-	4 x 50mm² + Earth	3 x 150mm² + Earth	4 x 185mm² + Earth
1 x 120mm² + Earth	-	4 x 70mm² + Earth	4 x 95mm² + Earth	4 x 240mm² + Earth
1 x 150mm² + Earth	-	1 x 185mm² + Earth	4 x 120mm² + Earth	1 x 500mm² + Earth
-	-	1 x 240mm² + Earth	4 x 150mm² + Earth	1 x 630mm² + Earth
-	-	-	1 x 300mm² + Earth	-
-	-	-	1 x 400mm² + Earth	-
All Hawke Power Connectors have a maximum working voltage of (750V AC). Other voltages and contact configurations also available contact us for details.

Power Calculations

To select the shell size of the connector, it is essential that you calculate the dissipated wattage of the arrangement. This ensures that the arrangement does not exceed the maximum permitted temperature classification with regard to the upper ambient temperature for the area of installation. (please refer to table 1 below for the maximum allowable dissipated wattage per connector size).

Dissipated Wattage Calculation

Equation definitions:

W = Dissipated wattage factor of the connector

N = The number of conductors to be terminated/number of contacts required. (Note: A contact comprises of a pin and socket).

I = The current requirement per contact. (Note: This must be equal to or less than the maximum current rating of the contact, as shown in table 2 above).

R = The combined cable and contact resistance (see table 2 above).

Values pertinent to these definitions must then be b into the relevant fields below to calculate the dissipated wattage (W) of your chosen arrangement:

Note: The result must be lower than the maximum figure shown in table 1 above, for the appropriate temperature class and ambient temperature).

e.g. T6 40°C ambient application with 4 x 95mm² conductors running at 160 amps.
N = 4 contacts
I = 160 amps
R = 0.000283 ohms (95mm² soldered combined cable and contact resistance)

Therefore W = 4 x 25600 x 0.000283 = 28.9 watts.
Therefore an Ex63P Connector should be specified for this application as the shell size can accommodate the required 4 x 95mm² pin / socket inserts (see insert selection table) and the resultant dissipated wattage (28.9 watts) is below the maximum permitted 30.2 watts (see table 1 above).

This equation can also be transposed to facilitate the calculation of the maximum number of conductors permitted in your selected connector (calculator 2 below ) and the maximum allowable current within the upper ambient temperature of your b (calculator 3 below).

2.
W	R	I	Maximum Number Of Conductors N

3.
W	N	R	Current (Amps) I
Note: The result must not exceed the maximum current rating of the contacts (see table 2 above)

Note: Unless otherwise requested, connectors will be marked as T5 with an upper ambient temperature of +40°C.

Order Codes

When ordering, select the relevant code from each block as shown in the example below:
Power/Exd-50-S-CR-A-4-50-S-FLFRC-A-1

Power	Select Code	Debion		Example Code
Protection	Exd	Flameproof		Exd
Shell Size	32	32		50
	40	40
	50	50
	63	63
	75	75
Material	B	Brass Note: (for single core cables, Brass must be used)		S
	S	Stainless Steel (as standard)
	N	Nickel Plated Brass
Connector Style	CP	Connector Plug		CR
	CR	Connector Receptacle
	BR	Bulkhead Receptacle
Internal Earth Size Note: Should be at least 50% of phase conductor size	A	50mm²		A
	B	70mm²
	C	95mm²
	D	120mm²
	E	150mm²
	F	185mm²
	G	240mm²
Number Of Contacts		See insert selection
Contact Type		Contact Type	Maximum Conductor Acceptance Diameter (mm)	50
	50	50mm²	9.5
	70	70mm²	11.5
	95	95mm²	13
	120	120mm²	14.5
	150	150mm²	16.5
	185	185mm²	18.5
	240	240mm²	20.5
	300	300mm²	25
	400	400mm²	29
	500	500mm²	32
	630	630mm²	38
	X	No Insert
Insert Type	P	Pin		S
	S	Socket
Accessories * Note: only the connector receptacle (CR) can be flange mounted.	FL	Mounting Flange *		FLFRC
	FPC	Flameproof Plug Cap
	FRC	Flameproof Receptacle Cap
	PPC	Environmental Plug Cap
	PRC	Environmental Receptacle Cap
Certification	A	ATEX/IECEx/EAC/INMETRO		A
	N	ATEX/IECEx/EAC/INMETRO /NEC 505 Voltage reduced to 600V
Ambient Rating & Temperature Class T5 +40°C will be supplied as standard if alternative not specified	1	T5 +40°C Standard		1
	2	T5 +50°C
	3	T5 +60°C
	4	T6 +40°C
	5	T6 +50°C
	6	T6 +60°C

Find A Connector Modifier

Ordering Inbation

For ordering inbation and codes, please see order codes tab.

中国区分销商：
上海颐品自动化科技有限公司
Shanghai Epin Automation Co.,Ltd.

Website:www.epinautomation。。ｃｏｍ
:sales@epinautomation.com
*: